If your hardwood floor is in generally fine shape, with only a damaged spot or two, it is easy and economical to make small repairs by replacing a strip or plank of flooring. You can also fix buckled areas of flooring and avoid having to completely refinish your floors. Most floors use a tongue-and-groove design for connecting.
floors on a concrete and wood under-floor, or to nail it on plywood. .. Recommended used for Engineered tongue & groove prefinished and preoiled floor. PREPARATION OF PLACES. The installation of a wood floor should be the last stage of your . ORIENTED STRAND BOARD (OSB): Panels must be installed with 90⁰.
P5 Tongue & Groove Chipboard Floor Panel (L)2400mm (W)600mm (T)18mm - B&Q for all your home and garden supplies and advice on all the latest DIY trends. . hard-wearing; easy to clean and look after; simple to install; warm underfoot - plus real wood top layer and laminate options work with underfloor heating.
Dec 5, 2008 . hardwoodinstaller Step by step procedures for removing and replacing a single solid hardwood floor board.
Tongue-and-groove flooring uses a system of interlocking edges – tongues and grooves – to stay in place with few nails. When floor planks get split or warped, replace them for aesthetic reasons and .
Cutting in a perfect-fit patch with This Old House general contractor Tom Silva.
Tongue and groove is a popular style of interlocking and securing wood panels. It can be used on floors, walls, ceilings and many other surfaces. Learn about tongue and groove panels and how your home can benefit from them.
Eased Edge: See Beveled Edge. End Joint: The place where two pieces of flooring are joined together end to end. End Lifting: A swelling of the top layer of engineered wood flooring, occurring at an end joint. End-Matched: In tongue-and-groove strip and plank flooring, the individual pieces have a tongue milled on one end.
Add architectural interest to a flat drywall ceiling with tongue and groove wood floors. . Open boxes of wood flooring, then use a measuring tape to determine the thickness of each plank. . Begin installation of wood flooring by starting in corner and paying attention as to which side of each plank is the "installation" side.
The tongue and groove joint has proved itself over centuries to be very simple, clean and strong. Popular uses for this joint are in the creation of doors, panels, and table tops. Another function for this joint is seen in hardwood floors. Unlike the other examples given, hardwood flooring is created solely with tongue and.
Step 2. tight shot of glue application. When installing additional rows, work from left to right. Apply wood glue to the tongue and groove seams, then connect the pieces, carefully folding and tapping the new piece to rest on the subfloor. Immediately wipe up any glue that squeezes through the boards.
Nov 22, 2010 . A 1918 bungalow in Mount Ranier, Maryland, displays beautiful, original tongue-in-groove pine floors that had been covered for decades by vinyl tiles—then subsequent layers of plywood, vinyl tiles, and carpeting—until they were refinished and restored in 2003. (Photo: Courtesy of City Lights Realty).
Jan 17, 2014 . The floor can either be secret nailed, secret screwed or glued directly down to the subfloor, or can be floated over an underlay by gluing along the length and width of the plank and pushing them together. Tongue and groove flooring is available in both solid wood and engineered wood, so can be fitted on.
Although laminate wood flooring is becoming popular, you may prefer real wood, shown here. Boards can be laid as a floating floor, nailed down or installed with adhesive. On a wood floor, you can remove old boards and install new ones, but not if a partition crosses the old boards. Check whether doors need to be trimmed.
Most wood flooring goes on a typical raised, wood-framed subfloor that is surfaced with plywood or OSB (oriented-strand board) subflooring panels. The subfloor must be clean, dry, flat, .. Fit a board for the second row so that its groove interlocks tightly with the tongue of the first row. Use a tapping block or small piece of.
Sep 28, 2014 . Cutting in a perfect-fit patch with This Old House general contractor Tom Silva. (See below for a shopping list and tools.) Click here to SUBSCRIBE to the of.
Here's a tip for cutting the groove. Stick the blade inside the groove and cut off the bottom from the inside (or use a table saw). Apply a bead of wood glue to all four edges of the new plank. Insert the glued tongue of the new plank into the groove on the existing flooring and drop the plank into place. Wipe off any excess glue.
Pulling up tongue-and-groove flooring can be tedious and time-consuming -- more so when the boards are glued -- but it's not a test of carpentry skills. . Wood flooring that has been glued can seldom be salvaged, but if has only been nailed, you may be able to work it into another project or even sell it to someone who.
Nov 5, 2013 . The wood we chose was basic tongue and groove (tongue in groove?) pine boards that you can find in the lumber section of your hardware store. . You could use any type of lumber you like for this project, but I really liked the idea of wider plank pine boards that would look a little more like they're original.